[ale] I've hit a rough wall, installin' Smoothwall :-)
Courtney Thomas
courtneycthomas at bellsouth.net
Sun Dec 21 09:56:11 EST 2008
William,
I'm looking to be a client in these matters, not a server :-)
I apologize for my poor communication which confused everyone in this regard and look forward to hearing back from you in this regard.
Cordially,
Courtney
----- Original Message -----
From: William Wylde
To: ale at ale.org
Sent: Sunday, December 21, 2008 9:28 AM
Subject: Re: [ale] I've hit a rough wall, installin' Smoothwall :-)
Unless you use g-mail or some other service that puts all their mail servers on non-standard ports. You'll have to look in their "help" sections to see, as I don't recall right off hand what even gmails settings are.
On Sat, Dec 20, 2008 at 5:45 PM, Dennis Ruzeski <denniruz at gmail.com> wrote:
Pop email is port 110/tcp. If you send, smtp is port 25/tcp
I use an encrypted filesystem for most of my sensitive docs. For
communication I only use ssl or encryption for ssh and secure http
connections. I have a ipcop firewall set up, which is very similar to
smoothwall and I also use iptables on linux and comodo firewall on
windows.
In addition to that I have a bandwidth monitor set up and I use snort
for my intrusion detection.
I'll be happy to go into detail about any of this with you. Just ask.
--Dennis
On Sat, Dec 20, 2008 at 1:02 AM, Courtney Thomas
<courtneycthomas at bellsouth.net> wrote:
> Thanks Dennis.
>
> I guess that covers web browsing but what about email ?
>
> By the way, what security protection other than a firewall do you use,
> please ?
>
> Encryption, and if yes, what do you use and for what purposes ?
>
> Cordially,
>
> Courtney
>
>
> ----- Original Message -----
> From: "Dennis Ruzeski" <denniruz at gmail.com>
> To: <ale at ale.org>
> Sent: Friday, December 19, 2008 10:43 PM
> Subject: Re: [ale] I've hit a rough wall, installin' Smoothwall :-)
>
>
>> I'm glad you're up and running--
>>
>> For a start, 80/tcp, 443/tcp, and 53/udp are important. That's http,
>> https, and dns, respectively.
>>
>> Others will depend on what applications you run and how they access
>> the net. (Streaming video, ftp, ssh, telnet, etc...)
>>
>> --Dennis
>>
>>
>>
>> On Fri, Dec 19, 2008 at 9:33 PM, Courtney Thomas
>> <courtneycthomas at bellsouth.net> wrote:
>>> Brian,
>>>
>>> You were right and so was I. I just didn't have enough sense to know it
>>> :-)
>>>
>>> There was nothing wrong with my setup. It's just that I didn't realize I
>>> needed to
>>> do a hard reset on the wireless router to apparently enable the router to
>>> detect and incorporate each parameter change as I was feeling my way.
>>>
>>> All now works as wanted ! Functionally.
>>>
>>> But I'm still not sure if I've properly implemented subnetting re: the
>>> router,
>>> lan and firewall. Comments ? [Please see initially submitted query for
>>> detail.]
>>>
>>> BUT......I have now half closed the firewall and would like to entirely
>>> close it, putting
>>> it in "closed" configuration, defined as.........
>>>
>>> "all outgoing requests are blocked and must be explicitly chosen ports
>>> and services required".
>>>
>>> How do I do this ?
>>>
>>> Which ports and services, at a minimum, do I need ?
>>>
>>> Cordially,
>>>
>>> Courtney
>>>
>>>
>>>
>>> ----- Original Message -----
>>> From: "Brian Pitts" <brian at polibyte.com>
>>> To: <ale at ale.org>
>>> Sent: Friday, December 19, 2008 8:42 PM
>>> Subject: Re: [ale] I've hit a rough wall, installin' Smoothwall :-)
>>>
>>>
>>>> Hi Courtney,
>>>>
>>>> Let's approach the problem a step at a time.
>>>>
>>>> 1) Connect the machine running smoothwall directly to the internet. The
>>>> goal here is to connect your modem to the "red" NIC so that interface
>>>> has the public IP address given to you by your internet service provider
>>>> (eg 216.77.188.41). If you have a cable modem this si probably as simple
>>>> as plugging it in. If you have a DSL modem from Bellsouth it may be set
>>>> up to act as a router; then you will need to figure out how to change it
>>>> to act as a bridge.
>>>>
>>>> 2) Configure your private network in smoothwall. I do not have any
>>>> experience doing this, but I imagine you assign a private IP address to
>>>> your "green" NIC (e.g. 192.168.1.1), set up a DHCP server to listen on
>>>> your "green" NIC and assign a range of addresses (eg 192.168.1.100 -
>>>> 192.168.1.200), and tell smoothwall to forward traffic from "green" to
>>>> "red".
>>>>
>>>> 3) Connect your ethernet hub to the "green" interface. You should be
>>>> able to connect your machines with wired NICS to the hub and access the
>>>> internet.
>>>>
>>>> 4) DON'T connect your wireless router to the hub or maching running
>>>> smoothwall yet. Plug in just the power cord. Connect to it from your
>>>> windows laptop. Log in to the linksys web interface. Turn off the
>>>> linksys DHCP server. The linksys should have fields to set up internal
>>>> and external IP addresses. Do not set up an external address. Give it an
>>>> internal address on the same network as your smoothwall box (e.g.
>>>> 192.168.1.2). Save these settings and unplug the linksys. NOW connect
>>>> one of the 4 internal ethernet ports on the linksys to one of the ports
>>>> on your hub using a crossover cable. Plug the linksys power back in.
>>>> Your should be able to access the internet from your machines with wifi
>>>> now.
>>>>
>>>> -Brian
>>>>
>>>> _______________________________________________
>>>> Ale mailing list
>>>> Ale at ale.org
>>>> http://mail.ale.org/mailman/listinfo/ale
>>>
>>> _______________________________________________
>>> Ale mailing list
>>> Ale at ale.org
>>> http://mail.ale.org/mailman/listinfo/ale
>>>
>> _______________________________________________
>> Ale mailing list
>> Ale at ale.org
>> http://mail.ale.org/mailman/listinfo/ale
>
> _______________________________________________
> Ale mailing list
> Ale at ale.org
> http://mail.ale.org/mailman/listinfo/ale
>
_______________________________________________
Ale mailing list
Ale at ale.org
http://mail.ale.org/mailman/listinfo/ale
------------------------------------------------------------------------------
_______________________________________________
Ale mailing list
Ale at ale.org
http://mail.ale.org/mailman/listinfo/ale
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mail.ale.org/pipermail/ale/attachments/20081221/0b7f710e/attachment-0001.html
More information about the Ale
mailing list