[ale] OT: Cisco 2900-XL configure another Vlan

Christopher Fowler cfowler at outpostsentinel.com
Thu Feb 9 17:21:23 EST 2006


Okay.  I think I got but not sure.

I followed these directions

http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/29_35xu/scg/kivlan.htm#59924

Here is my config
!
interface VLAN1
 no ip route-cache
!
interface VLAN500
 no ip route-cache
 shutdown
!
interface FastEthernet0/1
!
!
interface FastEthernet1/1
 switchport multi vlan 500
 switchport mode multiSwitch
!
#show interface Fa1/1 switchport
Name: Fa1/1
Operational Mode: multi
Administrative Trunking Encapsulation: isl
Operational Trunking Encapsulation: isl
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: NONE
Pruning VLANs Enabled: NONE

Switch#show vlan brief
VLAN Name                             Status    Ports
---- -------------------------------- ---------
-------------------------------
1    default                          active    Fa0/1, Fa0/2, Fa0/3,
Fa0/4,
                                                Fa0/5, Fa0/6, Fa0/7,
Fa0/8,
                                                Fa0/9, Fa0/10, Fa0/11,
Fa0/12,
                                                Fa0/13, Fa0/14, Fa0/15,
Fa0/16,
                                                Fa1/2, Fa1/3, Fa1/4,
Fa2/1,
                                                Fa2/2, Fa2/3, Fa2/4
500  VLAN0500                         active    Fa1/1
1002 fddi-default                     active    
1003 token-ring-default               active    
1004 fddinet-default                  active    
1005 trnet-default                    active    


Brief shows Fa1/1 on vlan 500.  But the show interface command shows it
on default.  Maye because the vlan is in 'shutdown' mode.  Do I need to
enable it?

what I'm trying to do is configure a VLAN on a switch in our colo rack
for a private subnet so I do not have to install another switch.  The
switch is our main switch for our public segment and I'm in need of a
private segment at the facility.






On Thu, 2006-02-09 at 17:10 -0500, Christopher Fowler wrote:
> A while back I got some help configuring a VLAN on a switch.  Now I need
> to configure another VLAN but the commands seem to be different.  IOS
> versions are different.
> 
> Switch#show vlan brief
> VLAN Name                             Status    Ports
> ---- -------------------------------- ---------
> -------------------------------
> 1    default                          active    Fa0/1, Fa0/2, Fa0/3,
> Fa0/4,
>                                                 Fa0/5, Fa0/6, Fa0/7,
> Fa0/8,
>                                                 Fa0/9, Fa0/10, Fa0/11,
> Fa0/12,
>                                                 Fa0/13, Fa0/14, Fa0/15,
> Fa0/16,
>                                                 Fa1/1, Fa1/2, Fa1/3,
> Fa1/4,
>                                                 Fa2/1, Fa2/2, Fa2/3,
> Fa2/4
> 1002 fddi-default                     active    
> 1003 token-ring-default               active    
> 1004 fddinet-default                  active    
> 1005 trnet-default                    active    
> 
> Now I try to configure a new vlan
> 
> Switch#configure terminal
> Enter configuration commands, one per line.  End with CNTL/Z.
> Switch(config)#vlan 500
>                 ^
> % Invalid input detected at '^' marker.
> 
> Switch(config)#
> 
> Here are the instructions I'm referencing:
> 
> http://www.ale.org/archive/ale/ale-2004-12/msg00636.html
> 
> 
> _______________________________________________
> Ale mailing list
> Ale at ale.org
> http://www.ale.org/mailman/listinfo/ale




More information about the Ale mailing list