[ale] Sound Blaster AWE 64 Help! (Long!)

Philip Rodgers p.rodgers at home.com
Tue May 4 19:23:02 EDT 1999


all i had to do for mine to work was run sndconfig and add
(verifyld n) at the top of the isapnp.conf file.  You can find more
documentation at
http://www.linuxhq.com/HOWTO/mini/Soundblaster-AWE-3.html#ss3.2
------------------------------------------------------------------------
Philip Rodgers
p.rodgers at home.com

"Any sufficiently advanced technology is indistinguishable from magic."
                                                Arthur C. Clarke
------------------------------------------------------------------------
----- Original Message -----
 From: Daniel S Cox <danny.cox at ecweb.com>
To: <ale at ale.org>
Sent: Tuesday, May 04, 1999 2:47 PM
Subject: [ale] Sound Blaster AWE 64 Help! (Long!)


> All,
>
> A wee problem (actually, it's driving me crazy, but that doesn't take but
> a gentle push).
>
> I purchased a Creative Labs SoundBlaster 64 AWE pnp (yeah, I know, but the
> docs say that it'll work).  I have a pnp modem that works just fine,
thanks.
>
> I've tried on several evenings to get this thing to work to no avail.  It
> works fine under that *other* OS wannabee.  I thought I'd hit paydirt when
> I discovered that the IRQ of both cards were set to 5, but it didn't make
a
> difference.
>
> I started with "sndconfig", a Red Hat thing (I think), which mostly set
> things up properly.  I had to tweak /etc/isapnp.conf myself.
>
> In checking the code that initializes the card, it checks for the constant
> 0xAA.  It always returns 0xFF, so the board never inits properly.  My
first
> guess is that I have an IRQ, Port or DMA conflict with another device, but
> /proc/{ioports,interrupts,dma} doesn't note that any of these are in use,
> or overlap.
>
> "isapnp /etc/isapnp.conf" reports no errors.  Adding "(DEBUG)" at the top
> prints the parsing and the execution of each statement, and still no
errors.
>
> The error message tracks the io port if I change it from 0x220 to 0x240,
> so I know the options are being set properly at load time.
>
> So: any more direction?  Any ideas?
>
> Much thanks in advance!  Machine description below, with config files.
>
> Danny
>
> Hardware description:
> Pentium 200 MHz MMX
> ASUS TX Motherboard
> 64MB Memory
> Std 2 IDE interfaces, on the mboard, 1 for 2 GB drive (Win...something), 1
> for ATAPI CDROM
> BusLogic 946C SHA
> 1 GB SCSI disk
> 4.5 GB SCSI disk
> 4mm DAT, Archive Python
> UMAX Scanner (on external SCSI bus)
> std 2 serial ports and 1 parallel, on mboard
> mouse, keyboard, monitor
>
> /etc/isapnp.conf (no comments) is:
> (READPORT 0x0203)
> (ISOLATE PRESERVE)
> (IDENTIFY *)
> (CONFIGURE AKY1003/822087295 (LD 0
>   (IO 0 (BASE 0x03e8))
>   (INT 0 (IRQ 5 (MODE +E)))
>   (ACT Y)
> ))
> (CONFIGURE CTL00e4/333648607 (LD 1
>  (INT 0 (IRQ 7 (MODE +E)))
>  (DMA 0 (CHANNEL 1))
>  (DMA 1 (CHANNEL 5))
>  (IO 0 (BASE 0x220))
>  (IO 1 (BASE 0x300))
>  (IO 2 (BASE 0x388))
>  (ACT Y)
> ))
> (WAITFORKEY)
>
> /etc/conf.modules:
> alias net-pf-4 off
> alias net-pf-5 off
> alias scsi_hostadapter BusLogic
> alias sound sb
> options opl3 io=0x388
> alias midi awe_wave
> post-install awe_wave /usr/bin/sfxload /etc/midi/GU11-ROM.SF2
> options sb io=0x220 irq=7 dma=1 dma16=5 mpu_io=0x300
>
> modprobe sb sez:
>
> Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
> sb_dsp_detect(220) entered
> sb: No response to RESET
> Doing ESS1688 address selection
> sb: No response to RESET
> sb: No response to RESET
> SB reset failed
> sb: dsp reset failed.
> /lib/modules/2.2.5/misc/sb.o: init_module: Device or resource busy
> sound: Device or resource busy
>
>






More information about the Ale mailing list